Excellent hydraulic seal manufacturer and supplier

Top o ring factory manufacturer: Without the pressure pushing them apart the two seal faces would be in full contact, this is known as dry running and would lead to rapid seal failure. Without the process pressure (and the force of the springs) pushing the faces together the seal faces would separate too far, and allow fluid to leak out. Mechanical seal engineering focuses on increasing the longevity of the primary seal faces by ensuring a high quality of lubricating fluid, and by selecting appropriate seal face materials for the process being pumped. When we talk about leakage we are referring to visible leakage of the seal. This is because as detailed above, a very thin fluid film holds the two seal faces apart from each other. By maintaining a micro-gap a leak path is created making it impossible for a mechanical seal to be totally leak free. What we can say, however, is that unlike gland packing, the amount of leakage on a mechanical seal should be so low as to be visually undetectable. See more information on rod seals manufacturer.

A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly.

Select the appropriate sealing material: There are many types of sealing materials, including many metals, plastics and rubbers. The same material has different performances from different companies. On the other hand, the same seal has different performances in different working conditions or different sealing schemes, so it must be carefully considered when choosing. Note: Be sure to consider seals under the premise of a reasonable sealing scheme, then consider the sealing material, and then consider the seal manufacturer. If you don’t have enough sealing experience, it is best to consider the sealing company first, and let the sealing company consider the sealing scheme and other issues, such as DMS Seals Technology Co.,Limited.

It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.

DMS SEALS’ s bonded seal is ideal for being applied to threaded pipe fittings and plug sealing in Metric, British and BSP systems. The seal has no special requirements for the positioning and processing techniques of the seal groove, so it is an ideal accessory for fast and automatic installation that we highly recommend. The operating temperature range is -30°C ~ 100°C, and the working pressure is less than 39.2 MPa. It is commonly used in a hydraulic oil medium.

Since the scraper seal is made of the special material, PTFE, it has an impurity immersion function. Therefore, when combined with the piston rod seal and the metal bushing, it can prevent damage to the piston rod and prevent the accumulation of oil pressure. It has a diameter range of 3-1600mm and a temperature range of -30°C + 200°C. The wiper scraper seal can operate at speeds of up to 5 m/s. It has high wear resistance, tear resistance, low-temperature resistance and good strength. Our wiper seals can be used in combination with piston seals and anti-wear rings to prevent oil in the cylinder from being mixed with foreign matter, which causes damage to the working seal. It is especially suitable for piston rods with a large diameter. Moreover, it has a wide range of applications, such as agricultural machinery, injection moulding machines, forklifts, cranes and so on.

Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.

We own a number of invention patents and leading production process. The R&D teams have the ability to design and develop seals for various of complicated working condition of sealing system. We have already passed the certification of ISO 9001 and IATF 16949. We have the mature technical reserve for the solution of ultra-high temperature, ultra-high pressure, ultra-low temperature, highly corrosive and other special working condition. Discover additional info on dmsseals.com.

DMS Seals is a professional mechanical seals manufacturer and oil seal supplier for hydraulic seals, O-Rings, spring energized seals, oil seals, mechanical seal and so on. Hydraulic seals including step seals, glyd rings, guide strips, wiper seals, rod seals, piston seals, rotary seals, wear rings. We can provide the hydraulic seals with bronze filled PTFE, carbon filled PTFE, graphite filled PTFE, MoS2 filled PTFE, glass filled PTFE, virgin PTFE. About O-Rings, we can supply NBR, FKM, silicone, EPDM, HNBR, ACM, FFKM material.